The article which follows about Tools You Need to Install a New Bathtub is really interesting. You should investigate for yourself.
Mounting a bathtub isn't precisely brain surgery, but it does need strong plumbing, woodworking, and also in some cases, tiling abilities. Changing an old bathtub with a new one is likewise a reasonably hard task. If the old bathtub is readily available, the job can relocate easily; if you need to open up a wall surface to get rid of the old bathtub and also place the brand-new bath tub, the job is a lot harder. In either instance, the job is within a house handyman's skills, although you will need a helper to move out the old tub and set in the new one. Make sure you have actually certified on your own for the task as well as are comfortable attempting it. As opposed to working with a contractor to take over a halfway-completed project, it is better to consider employing one before you begin. Possibilities are you may need a specialist plumber to make tube links.
This write-up will certainly aid you mount a brand-new bath tub in your washroom if you have actually already purchased a new tub and don't need to transform the setup of your previous water system pipelines.
Your devices as well as material checklist should comprise the following:
Preparing for the Installation
To start with, the sustaining framework supplied with the bath needs to be fitted (if called for) according to the maker's directions. Next, fit the taps or mixer to the bath tub. When suitable the tap block, it is essential to make sure that if the faucet includes a plastic washer, it is fitted in between the bathroom as well as the taps. On a plastic bathroom, it is likewise practical to fit a supporting plate under the faucets system to avoid strain on the bath tub.
Fit the versatile tap connectors to the bottom of both taps using 2 nuts and also olives (often supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and after that pass the outlet via the hole in the bathroom. Use the nut provided by the producer to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the flexible overflow pipeline to the overflow outlet. Afterwards, screw the pipeline to the overflow face which should be fitted inside the bathroom. See to it you utilize every one of the supplied washers.
Link the catch to the bottom of the waste outlet on the bath tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the trap to the electrical outlet. Connect all-time low of the overflow tube in a similar manner.The bathroom ought to currently be ready to be suited its final placement.
Removing Old Taps
If you require to replace old faucets with new ones as a part of your installment, then the first thing you need to do is detach the water. After doing so, switch on the faucets to drain any kind of water remaining in the system. The procedure of removing the existing faucets can be quite troublesome as a result of the restricted accessibility that is often the situation.
Use a basin wrench (crowsfoot spanner) or a faucet device to undo the nut that attaches the supply pipes to the taps. Have a towel ready for the staying water that will certainly come from the pipelines. Once the supply pipes have actually been removed, utilize the very same tool to loosen the nut that holds the faucets onto the bath/basin. You will need to quit the solitary taps from transforming throughout this process. When the faucets have actually been removed, the holes in the bath/basin will certainly need to be cleaned of any type of old securing substance.
Before carrying on to fit the brand-new taps, compare the pipeline links on the old faucets to the new taps. If the old faucets are longer than the brand-new taps, then a shank adapter is needed for the brand-new faucets to fit.
Installing the Tub
Utilizing both wooden boards under its feet, place the tub in the needed placement. The wooden boards are useful in uniformly spreading out the weight of the bath tub over the area of the boards instead of focusing all the weight onto 4 tiny factors.
The next goal is to make sure that the tub is leveled all round. This can be attained by examining the spirit level and changing the feet on the tub up until the level reviews degree.
To mount taps, fit the bottom of the furthest versatile tap port to the proper supply pipeline by making a compression sign up with; after that do the very same for the various other faucet.
Activate the water supply and check all joints and new pipework for leaks and tighten them if required. Fill up the tub and likewise inspect the overflow outlet as well as the typical outlet for leaks.
Lastly, deal with the bathroom paneling as defined in the supplier's user's manual. Tiling and also securing around the tub must wait up until the tub has been utilized at least once as this will resolve it into its final placement.
Suitable New Taps
If the tails of the new faucets are plastic, after that you will need a plastic adapter to avoid damage to the thread. One end of the adapter fits on the plastic tail of the faucet and the various other end supplies a connection to the existent supply pipelines.
If you need to fit a monobloc, then you will certainly need decreasing couplers, which attaches the 10mm pipeline of the monobloc to the basic 15mm supply pipeline.
Next, place the tap in the placing hole in the bath/basin making certain that the washing machines are in location between the faucet and the sink. Protect the tap in place with the manufacturer supplied backnut. Once the faucet is firmly in place, the supply pipes can be linked to the tails of the faucets. The taps can either be attached by using corrugated copper piping or with regular tap ports. The former type needs to be linked to the faucet ends first, tightening up only by hand. The supply pipelines can later be linked to the various other end. Tighten both ends with a spanner after both ends have been linked.
Tiling Around the Bathtub
In the location where the bath satisfies the tile, it is needed to seal the joins with a silicone rubber caulking. This is important as the installation can move enough to fracture a stiff seal, creating the water to permeate the wall surface between the bathroom and the tiling, causing complications with moisture and also possible leakages to the ceiling below.
You can select from a selection of coloured sealants to assimilate your components as well as installations. They are sold in tubes as well as cartridges, and also are capable of securing voids up to a size of 3mm (1/8 inch). If you have a bigger gap to fill up, you can fill it with spins of soaked newspaper or soft rope. Bear in mind to always fill up the bath tub with water prior to sealing, to enable the activity experienced when the tub is in usage. The sealer can break relatively very early if you do not take into account this motion prior to sealing.
Alternatively, ceramic coving or quadrant ceramic tiles can be made use of to edge the bath or shower tray. Plastic strips of coving, which are easy to use as well as reduce to dimension, are also quickly readily available on the marketplace. It is advisable to fit the ceramic tiles utilizing waterproof or water-proof adhesive as well as cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
As an avid person who reads on A Step-by-Step Guide to Installing a Bathtub, I was thinking sharing that excerpt was really useful. Liked our blog entry? Please share it. Let someone else check it out. We take joy in reading our article about Installing A Bathtub.
Pricing